Can I Install A Bath Tub Myself?
Or Book Technician HereRight here in the next paragraph you might get more sensible insights around A Step-by-Step Guide to Installing a Bathtub.
Mounting a tub isn't specifically rocket science, however it does require solid plumbing, woodworking, as well as occasionally, tiling skills. Changing an old bathtub with a new one is likewise a reasonably challenging task. If the old tub is easily obtainable, the project can relocate quickly; if you need to open a wall to get rid of the old tub as well as place the brand-new tub, the job is much harder. In either situation, the job is within a residence handyman's skills, although you will certainly require an assistant to move out the old tub and also set in the new one. Make certain you have actually qualified yourself for the work and also are comfortable attempting it. As opposed to hiring a contractor to take over a halfway-completed job, it is far better to take into consideration utilizing one prior to you begin. Possibilities are you may require a professional plumber to make tube connections.
This post will certainly help you set up a brand-new bathtub in your shower room if you have actually currently purchased a brand-new bathtub and don't require to transform the arrangement of your previous supply of water pipelines.
Your devices and material list need to comprise the following:
Preparing for the Setup
To start with, the sustaining frame supplied with the bath must be fitted (if required) according to the producer's directions. Next off, fit the faucets or mixer to the bathtub. When fitting the tap block, it is essential to make sure that if the tap comes with a plastic washer, it is fitted between the bath and also the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets system to avoid stress on the tub.
Fit the versatile tap connectors to the bottom of the two taps making use of 2 nuts and also olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet through the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. Make sure you make use of every one of the supplied washers.
Attach the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach all-time low of the overflow tube in a similar manner.The bath need to currently be ready to be fitted in its last setting.
Removing Old Taps
If you need to replace old faucets with brand-new ones as a part of your setup, then the first thing you need to do is detach the supply of water. After doing so, turn on the faucets to drain any water continuing to be in the system. The process of removing the existing faucets can be rather problematic as a result of the restricted accessibility that is commonly the situation.
Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipelines to the faucets. Have a fabric ready for the continuing to be water that will originate from the pipes. As soon as the supply pipes have actually been eliminated, use the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from turning throughout this process. As soon as the taps have actually been eliminated, the holes in the bath/basin will need to be cleaned of any type of old sealing substance.
Before carrying on to fit the new faucets, compare the pipeline connections on the old faucets to the new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the new faucets to fit.
Setting up the Bathtub
Utilizing the two wood boards under its feet, place the bath tub in the needed position. The wood boards are useful in equally spreading the weight of the bath tub over the area of the boards instead of concentrating all the weight onto four little points.
The following goal is to make sure that the bathtub is leveled all round. This can be accomplished by checking the level and readjusting the feet on the bathtub up until the spirit level checks out degree.
To set up faucets, fit the bottom of the outermost flexible faucet adapter to the suitable supply pipeline by making a compression sign up with; then do the exact same for the various other faucet.
Switch on the water system and also check all joints as well as brand-new pipework for leaks and tighten them if needed. Load the bathtub and likewise inspect the overflow electrical outlet and the typical electrical outlet for leakages.
Finally, repair the bath paneling as defined in the supplier's instruction manual. Tiling as well as securing around the bath tub should wait up until the tub has actually been made use of at least once as this will resolve it right into its last setting.
Suitable New Taps
If the tails of the new faucets are plastic, after that you will need a plastic port to stop damage to the thread. One end of the port fits on the plastic tail of the faucet and the other end supplies a link to the existent supply pipes.
If you need to fit a monobloc, after that you will certainly require decreasing couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next, position the faucet in the placing opening in the bath/basin ensuring that the washers are in location in between the faucet and also the sink. Secure the tap in place with the maker supplied backnut. As soon as the faucet is firmly in place, the supply pipes can be connected to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with regular faucet adapters. The previous kind needs to be connected to the tap ends first, tightening only by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Tub
In the area where the bath satisfies the ceramic tile, it is needed to seal the joins with a silicone rubber caulking. This is very important as the installation can relocate sufficient to split a stiff seal, triggering the water to penetrate the wall surface in between the bathroom and also the tiling, causing issues with moisture as well as possible leaks to the ceiling below.
You can choose from a variety of coloured sealers to assimilate your components as well as fittings. They are offered in tubes and also cartridges, as well as can sealing gaps up to a size of 3mm (1/8 inch). If you have a bigger space to fill up, you can fill it with twists of drenched paper or soft rope. Keep in mind to always load the tub with water before securing, to enable the movement experienced when the bathtub remains in use. The sealer can split fairly very early if you do not think about this movement prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally quickly readily available on the marketplace. It is recommended to fit the ceramic tiles using waterproof or water-proof sticky and cement.
How to Install a Freestanding Bathtub?
Installing a freestanding bathtub or any kind of bathtub is not a difficult task if you have a sophisticated guide on installing a freestanding bathtub in your bathroom. Aside from getting the freestanding bathtub to your bathroom, you can do all the work without paying a plumber. A bathroom with a bathtub is a retreat where you can feel the sensation of coming home and soaking in that hot water. It is a great way to remove all the stress from your day.
This guide will walk you through installing a freestanding bathtub in simple steps and help you find relief.
Slope
Make sure your bathroom has a proper slope. If your floor lacks a slope, the water flow to the drain will not function, which leads to a blocked drain which can cost you money. You can use the level device to see your bathroom's vertical and horizontal aspects. Once you have that information, you must carry out the next step.
Placement
A freestanding bathtub has a unique characteristic that helps you bring elegance to your bathroom. A freestanding bathtub comes in various sizes and shapes suitable for different types of bathrooms.
According to the information you gathered from the level device, you must pick a bathtub that suits your style and fits your bathroom aesthetically. You can place a freestanding bathtub virtually anywhere, such as in the corner, near the wall, or even at the center of your bathroom. However, you must ensure proper plumbing where you want to install the tub. If not, then you must call a plumber.
Clean the bathroom floor
After deciding where to place the bathtub, you must clean the entire bathroom floor so that the dust and debris do not accumulate underneath the tub. Simple cleaning is enough, and you will clean it again after the installation.
Steps to Install a Freestanding Bathtub:
STEP 1: Place the protective blanket in the adjacent area where you want to install the bathtub. It will help you protect the bathtub's sides when you do the installation.
STEP 2: Now, place the 4x4 lumber in the area where you want to install the bathtub. Place the bathtub on top of the lumber, and align the drain line with the bathtub drain.
STEP 3: A freestanding bathtub comes with a drain kit. If not, make sure you purchase one with your bathtub. You can pop that drain kit and align it with your bathroom drain line. Ensure that you tighten the drain nut enough so there is no water leakage. You must also clean the bathtub’s drain to remove the factory dirt and debris.
STEP 4: Clean the drain hole in your bathroom. It helps to do the installation without any water blockage. A drain cleaner or bleach will suffice. Once the drain dries entirely, take a small amount of clear silicon and place it around the underside of the pipe flange.
STEP 5: Attach the drain tailpiece to the bottom of the bathtub. Place the rubber or plastic bushing with the plumbing material at the top of the tailpiece and screw the drain nut up the tube until it tightens both the bathtub’s drain and the drain tailpiece. Now you must add the lubricant to the seal to ensure there is no water leakage in the pipe connection.
STEP 6: Place caulk around the bottom edge of the bathtub. Take out the lumbar support and carefully bring the bathtub to the floor. Use a damp cloth to clean the excess caulk and debris and plumber putty to cover the tub drains and the floor.
Tips to Maintain a Freestanding Bathtub:
Always look for the clog in the drain. You can pull it out with a small stick if hair or debris is in the gutter. Use mild cleaning components, which will help you preserve the bathtub for a long time and will also help you remove surface-level scratches. Do not use strong solutions such as concentrated bleach to remove stains. Instead, mix water and diluted bleach with a ratio of 10:2, respectively. Apply it to the tub's surface and leave it for 15-20 minutes to remove any surface-level stains. Always check the floor drain. You may unclog it using any small sticks or a small vacuum to suck out all the debris. Check the heater or faucet immediately if you smell rust or grease in the water. Rust in the water may stain or damage the bathtub in the long run. If you want to sand the bathtub, try using 400 grit sandpaper or 600 grit sandpaper for a more refined finish.
Hopefully you enjoyed reading our piece on A Step-by-Step Guide to Installing a Bathtub. Many thanks for taking a few minutes to browse our piece. You should take a moment to distribute this page if you liked it. Thanks a lot for your time. Visit us again soon.
Book An Appointment